Shenzhen Hoion Lighting Co.,Ltd
Products

rgb led touch controller RGB LED Touch Controller Manual

HX-SZ100-WP-RGB, adopt the most advanced PWM (Pulse Width Modulation) digital dimming technology, especially design for RGB led strip. Adopt full touch RF wall panel remote control. 5 function buttons and 1 color ring in the center, all buttons are in touch form, the color ring has 64 levels in...

    HX-SZ100-WP-RGB, adopt the most advanced PWM (Pulse Width Modulation) digital dimming
    technology, especially design for RGB led strip. Adopt full touch RF wall panel remote control. 5 function
    buttons and 1 color ring in the center, all buttons are in touch form, the color ring has 64 levels in different
    color value. Further, there are 9 dynamic modes in the mode button, and the speed is adjustable.
    Particularly, the wall panel adopts RF wireless technology, and the working voltage is AC90-265V, easy
    and convenient to install.
    Especially, HX-SZ100-WP-RGB designed with Synchronization function. It is convenient to use
    RJ45 connector to connect the multiple controllers together, and achieve the synchronization function of
    thousands meters led strips.

    Technical Parameters:
    Receiver:

    Working temperature -20-60℃
    Supply voltage DC12V~24V
    0utput 3 channels
    Connecting mode common anode
    External dimension L127*W41*H32 mm
    Packing size L147*W85*H73 mm
    Net weight 190g
    Gross weight 220g
    Output gray 256 levels
    Output current <6A(each channel)
    Output power 12V:<216W, 24V:<432W
    Frequency of RF remote control 433.9MHz

    RF Wall panel remote control:
    Working voltage:AC90-265V(50/60Hz)
    RF signal frequency:433.92MHz
    Transmission distance:up to 30m(the deviation depend on the environment)
    Working power:<2W
    Standby power:<0.2W
    Ambient temperature:0-45℃
    Dimension:86*86*40mm
    Packing dimension: L89*W40*H89mm
    N.W.:130g
    G.W: 140g

    Power and Payload interface:



    Adopt male and female connector with screw.

    This product adopts RF full touch control, with one dimming ring and 5 function buttons.

    The function of each button as below:




    Important: As RF signal sender, set up the LED Touch faceplate to a RF led driver (RF receiver) before
    use.
    1. Press and hold the ¡Mode¡ key before the ¡RF LED Driver¡ powering on, the RF signal light lights red.
    2. Power up the ¡RF LED Driver¡, and the LEDs will output 50% brightness (Tip: if the output does not
    output 50% brightness, indicating that the code learning is not successful, need to repeat the step 1).
    3. Press the ¡ON¡ key, then the LEDs will be 25% brightness.
    4. Press the ¡Mode¡ key again, then the LEDs will be 5% brightness.
    5. Press the ¡ON¡ key again,then the LEDs will be 100% brightness,and indicating the successful code
    learning. If not, repeat from step 1.
    Installation Method
    1) Opening: Gently pry gaps in touch panel with a screwdriver, and remove the panel slowly, as
    shown below:



    2)Unplug the connector, connect the power cord, and fix the base part in the 86*86 installation box
    ( user need to prepare the installation box by themselves) on the wall with screws.

    3)Reconnect the two parts of panel, and cover the face part on the base part to complete
    the installation.

    Hot Tags: rgb led touch controller,rgb led touch controller manual, manufacturer, supplier, factory, company

    Product Categories

    Fast Track

    • Feedback
      Shenzhen Hoion Lighting Co.,Ltd welcomes your comments! Please fill this form to give us feedback or report any problem when experiencing our website.
    • Quick Navigation
    • Contact Us
      Address: 6-7F, Huichuan Science And Technology Park, Xiangyin Road, Nanlian, Longgang, Shenzhen, China
      Tel: 86-755-27966554    
      Fax: 86-755-29707831    
      E-mail: hoionlighting@led-ctrl.com
    Copyright © Shenzhen Hoion Lighting Co.,Ltd