Shenzhen Hoion Lighting Co.,Ltd
Products

rgb led wall controller RGB Wall Controller

Product Description HX-SZ600-WP-RGB, adopt the most advanced PWM (Pulse Width Modulation) digital dimming technology, especially design for RGB led strip. Adopt full touch RF wall panel remote control. 5 function buttons and 1 color ring in the center, all buttons are in touch form, the color...

Product Description
HX-SZ600-WP-RGB, adopt the most advanced PWM (Pulse Width Modulation) digital dimming technology, especially design for RGB led strip. Adopt full touch RF wall panel remote control. 5 function buttons and 1 color ring in the center, all buttons are in touch form, the color ring has 64 levels in different color value. Further, there are 9 dynamic modes in the mode button, and the speed is adjustable. Particularly, the wall panel adopts RF wireless technology, and the working voltage is AC90-265V, easy and convenient to install.
Especially, HX-SZ600-WP-RGB designed with Synchronization function. It is convenient to use RJ45 connector to connect the multiple controllers together, and achieve the synchronization function of thousands meters led strips.

Technical Parameters

Receiver:

Working temperature

-20-60℃

Supply voltage

DC12V~24V

0utput

3 channels

Connecting mode

common anode

External dimension

L91*W88*H24 mm

Packing size

L106*W106*H66 mm

Net weight

190g

Gross weight

220g

Output gray

256 levels

Output current

<8A(each channel)

Output power

12V:<288W,24V:<576 W

Frequency of RF remote control

433.9MHz

RF Wall panel remote control:

●Working voltage:AC90-265V(50/60Hz)
●RF signal frequency:433.92MHz
●Transmission distance:up to 30m(the deviation depend on the environment)
●Working power:<2W
●Standby power:<0.2W
●Ambient temperature:0-45℃
●Dimension:86*86*40mm
●Packing dimension: L89*W40*H89mm
●N.W.:130g
●G.W: 140g

External Dimension

Interface Specifications

Direction for use
This product adopts RF full touch control, with one dimming ring and 5 function buttons.

The function of each button as below:

Name of key

Instruction

Remarks

ON/OFF

ON or OFF in any time


Pause

Pause or Continue


Mode

The mode will move to next, when touch the key each time

9 modes in total.

Speed/Brightness +

The Speed/Brightness will +1, whentouch the key each time

Speed for dynamic modes, Brightness for static modes.

Speed/Brightness -

The Speed/Brightness will -1, when touch the key each time

Speed for dynamic modes, Brightness for static modes.

Color Ring

Touch any color which is wanted


9 modes in total as below:

No

Patterns

Remarks

1

Static worm white

Brightness is adjustable, speed is unadjustable

2

Static cool white

3

White breath

Speed is adjustable, brightness is unadjustable

4

Seven-color jumpy changing

5

Seven-color smooth

6

Seven-color fade

7

R/B crossfade

8

B/G crossfade

9

G/R cross fade

Important: As RF signal sender, set up the LED Touch faceplate to a RF led driver (RF receiver) before use.
1.Press and hold the "Mode" key before the "RF LED Driver" powering on, the RF signal light lights red.
2.Power up the "RF LED Driver", and the LEDs will output 50% brightness (Tip: if the output does not output 50% brightness, indicating that the code learning is not successful, need to repeat the step 1).
3.Press the "ON" key, then the LEDs will be 25% brightness.
4.Press the "Mode" key again, then the LEDs will be 5% brightness.
5.Press the "ON" key again,then the LEDs will be 100% brightness,and indicating the successful code learning. If not, repeat from step 1.

Installation Method
1)Opening: Gently pry gaps in touch panel with a screwdriver, and remove the panel slowly, as shown below: 


2)Unplug the connector, connect the power cord, and fix the base part in the 86*86 installation box ( user need to prepare the installation box by themselves) on the wall with screws.

3)Reconnect the two parts of panel, and cover the face part on the base part to complete the installation.

Typical Applications

Application Circuit 1:

Application Circuit 2: (Synchronization function with network Line(RJ45) )

Notes
1. Supply voltage of this product is DC12V~24V, never connect to others or AC220V.
2. Lead wire should be connected correctly according to grade that connecting diagram offers.
3. This product is not to overload;
4. Warranty of this product is one year, but exclude the artificial situation of damaged or overload working.

Common Problems

Problems

Possible cause

Solution

  1. Lamp does not light after power

Power cord is not properly connected, or there is not output switching power supply

Connect the power cord properly or replay the power

Lamp power cord is not connected or short circuit

Connected lighting power cord

2. After connecting some of the load the controller does not work

The connected load is too large,so that it has burned in some of the components of the controller

Replace parts of components or replace the controller



Hot Tags: rgb led wall controller,rgb wall controller, manufacturer, supplier, factory, company

Product Categories

Fast Track

  • Feedback
    Shenzhen Hoion Lighting Co.,Ltd welcomes your comments! Please fill this form to give us feedback or report any problem when experiencing our website.
  • Quick Navigation
  • Contact Us
    Address: 6-7F, Huichuan Science And Technology Park, Xiangyin Road, Nanlian, Longgang, Shenzhen, China
    Tel: +86-755-27966554    
    Fax: 86-755-29707831    
    E-mail: hoionlighting@led-ctrl.com
Copyright © Shenzhen Hoion Lighting Co.,Ltd